AJD 132

Producer

John Deere

Engine Model

4045HFG20 (122kW)

Cylinder and Design

4 cylinders - in line

Bore and Stroke (mm)

106 X 127

Total Cylinder Volume (L)

4.5

Compression Ratio

17.0:1

Engine Speed (rpm)

1500

Standby Power (kW/hp)

122/164

Prime Power(kW/hp)

112/150

Block Heater (Adt)

1

Block Heater Power (Watt)

750

Governor System

Mechanic

Air Filter<br>

Dry Type

Air intake

Turbocharged and Air Aftercooled

Oil Capacity (L)

20.5

Fuel Type

Diesel

Injection Type

Direct Injection

Fuel Pump Type

Delphi DP100G

Operating Voltage (Vdc)

12 Vdc

Battery and Capacity (Unit/Ah)

1x66

Cooling Method

Water Cooled

Coolant Capacity (engine only)l (gal)

9

Exhaust Gas Flow (m³/min)

23.6

Exhaust Back Pressure in-Hg (kPa)

7.5

Exhaust Gas Temperature ⁰C (F)

610

Total Cooling Water Capacity (l)

23

Fuel Consumption at 50% Prime Load l/h (kg/h)

15.1

Fuel Consumption at 75% Prime Load l/h (kg/h)

21.6

Fuel Consumption at 100% Prime Load l/h (kg/h)

28.3

Producer

Mecc Alte

Alternatrr Model

ECP 34-1M/4 C

Frequency (Hz)

50

Power (kVA)

125

Voltage (V)

400

Phalse

3

A.V.R.

DSR

Voltage Regulation

1

Insulation Class

H

Protection Class

IP23

Nominal Power Factor

0.8

Total Generator Weight (kg)

370

Cooling Air (m³/min)

29.2

Generator and Control Module Model

DSE 6120

Standard Devices

DSE model 6120, Auto Mains Failure control module, Static battery charger input 198-264 volt, output 27,6V 5A (24V) or

13,8 Volt 5A (12V), fuses for control circuits. This Control Module is suitable for a wide variety of single gen-set applications

Control Unit

- The DSE 6120 module has been designed to monitor generator frequency, volt, current, engine oil pressure, coolant

temperature running hours and battery volts.

- Module monitors the mains supply and control the switch over to the generator when the mains power fails.

- The DSE6120 also indicates operational status and fault conditions, Automatically shutting down the Gen. Set and giving

true first up fault condition of Gen. Set failure.The LCD display indicates the fault.

Construction and Painting

Components installed in sheet steel enclosure. Phosphate chemical, pre-coating of steel provides corrosion corrosion-resistant surface. Polyester composite powder topcoat forms a high gloss and extremely durable finish. Lockable and hinged panel door provides easy access to components.

Assembly

Control panel is mounted on baseframe with steel stand. Located at the right side of the generator set (When you look at the Gen.Set. from Alternator side)

- Engine speed

- Oil pressure

- Coolant temperature

- Run time

- battery volts

- Configurable timing

- Fail to start

- Emergency stop

- Low oil pressure

- High coolant temperature

- Over /Under speed

- Under/over generator frequency

- Under/over generator voltage

- Oil pressure sensor open

- Coolant temperature sensor open

- Charge failure

- Battery Low/High voltage

- Fail to stop.

- Low /High generator voltage

- Under /Over generator frequency

- Over /Under speed

- Low oil pressure

- High coolant temperature

- Voltage (L-L, L-N)

- Current (L1-L2-L3)

- Frequency

- Gen. Set ready

- Gen. Set enabled

- Generator over current

- Mains ready

- Mains enabled

Options

- Flexible sensor can be controlled with temperature, pressure, percentage (warning/shutdown/electrical trip)

- Local setting parameters and monitoring from PC to control module with USB connection (max 6 mt).

Options Control Panel Compatibility List

- Electrical Safety / Electro Magenetic Compatibility (EMC)

- BS EN 60950 Electrical Safety

- BS EN 61000-6-2 EMC Generic Immunity Standard

- BS EN 61000-6-4 EMC Generic Emission Standard

Static Battery Charger

- Battery charger is manufactured with switching-mode and SMD technology and ıt has high efficiency.

- Battery charger models' output V-I characteristic is very close to square and output is 5 amper, 13,8 V for 12 volt and

27,6 V for 24 V . Input 198 - 264 volt AC.

- The charger is fitted with a protection diode across the output.

- Connect charge fail relay coil between positive output and CF output.

- They are equipped with RFI filter to reduce electrical noise radiated from the device.

- Galvanically isolated input and output typically 4kV for high reliability.

Canopy

AK 49

1. Steel structures 
2. Emergency stop push button 
3. Control panel is right side of the set. 
4. Corrosion.resistant locks and hinges 
5. Sump drains valves 
6. Sound proof foam metarial 
7. Lifting Points 

Introductıon

Sound–attenuated and Weather-protective Enclosures Sound-attenuated and weather protective enclosures for generating sets from Aksa, meet event the sound requirements and provide optimum protection from inclement weather and development by our specialist acoustic engineers. Our modular designed sound insulated canopies provide ease of access for servicing and general maintenance and interchangeable components permitting on-site repair. Enclosures are designed to optimize genset cooling performance, providing you with confidence that genset ratings and ambient capability.

General Characteristics

Compact footprint, low profile design. 
Enclosure, generator set, exhaust system and fuel tank are pre-ssembled, pre-integrated and shipped as one package 
Body made from steel components treated with polyester powder coating 
Fire retardant foam insulation 
Easy access to all service points 
Exhaust system inside canopy 
Large doors on each side 
Control panel viewing window in a lockable access door 
Emergency stop push button mounted on enclosure exterior 
Cooling fan and battery charging alternator fully guarded 
Fuel fill and battery can only be reached via lockable access doors. 
Lifting points on the top of canopy and base frame 
Customer options available to meet your applications needs. 
Aksa makes its generating sets' noise level tests in accordance with directive 2000/14/EC validation of the noise level test has been aproved by the notified body Szutest

Length (mm)

3404

Width (mm)

1136

Height (mm)

2020

Fuel Tank Capacity (l)

340